Create a Cozy Jntuanantapur Pet Bed
Do you have a pet that loves to snuggle under the covers? We do! One of our recent adoptees, Rocky, cannot sleep unless he is nestled beneath the covers. It turns out that this behavior is normal. Dogs are den animals and certain breeds tend to burrow more than others. Dachshunds, in particular, were bred to burrow. Since Rocky is half dachshund, it makes perfect sense. When we gave him a regular pet bed with a blanket on top, he would get under and squirm until he was comfortable. All that squirming would cause the blanket to fall off. We have the perfect solution: the pet snuggle bed.
Dog Laying in Pet Bed with Blanket
Some dogs love to snuggle under covers.
- fleece fabric in contrasting colors
- tape measure
- sewing machine (not shown)
- thread in coordinating colors (not shown)
- pillow insert (not shown)
Snuggle Pet Bed Supplies
Fleece is the best type of fabric to use for a pet bed.
A Note on Fabric
Fleece is a wonderful fabric to use for this project. It’s inexpensive and comes in a variety of colors and patterns. It’s washable and will not shrink. The best part of fleece is that it will not fray after it’s cut. This saves a ton of time when sewing because it’s not necessary to hem the edges.
Cutting the Fabric
Some sewing and a little math are required to make this bed. As long as you can sew a straight line, this bed is not hard to make. This particular bed was made from a square pillow insert. The bed can be made with any size pillow you want. You will need to determine the size of the rectangle you will need to make an envelope style pillow cover. Here’s the basic formula:
pillow insert height + 1 inch = X
(pillow insert length x 2) + 6 inches = Y
For example, the pillow insert used for Rocky’s bed was 24 x 24 inches:
24 inches + 1 inch = 25 inches (X)~height
(24 inches x 2) + 6 inches = 54 inches (Y)~length
The rectangle for 24 x 24 pillow insert needs to be 25 inches (height) x 54 inches (length).
Make the Pillow Cover
Pin Down the Envelope Flat of the Cushion Cover
Use as many pins as needed to keep the fabric together while sewing.
Once the rectangle is cut to its proper size, it is time to pin the envelope part of the cushion cover. Lay the fabric with the right side (in the case of fleece, the fuzzier side) facing up. Fold the left and right edges in, overlapping them by 4 inches. Measure it to make sure it matches the pillow insert’s dimensions or lay your pillow insert on top. You should have at least an inch of space all around it. Pin it in place then sew the top and bottom with a 1 inch seam allowance.
Pet Snuggle Bed Envelope Cushion Cover
An envelope cushion cover requires minimal sewing.
Turn the cover inside out and ta-da; you have a pillow cover! Go ahead and insert the pillow to ensure a good fit. Remove the insert before you start the next step.
For the Blanket Top:
The top of the snuggle bed will require a piece of fleece that is larger than the insert. This will allow your pet to fit under the cover. It needs to be as wide as the bottom envelope cover for the pillow and at least 6-10 inches longer. It really depends on how big your pet is and how much blanket space is needed. For Rocky’s bed the top fabric was cut to these dimensions:
25 inches (height) x 35 inches (length)
Add the Top Fabric
Pin the Top Piece of Fleece to the Envelope Cushion Cover
It's easier to pin the corners and middle of the fabric first.
Lay the bottom envelope cover down with the insert opening facing the bottom. Now it’s time to pin the contrasting blanket on top. Since the blanket part of this pet bed is larger than the bottom, it will need to be pleated in order to make it fit. A pleat is a fold (or folds) in the fabric, where the fabric is doubled back on itself and sewn in place.To do this, start with pinning the corners of your top piece of fabric to the four corners of your pillow cover base. Then, find the midpoint of each side and pin it down. Pin the midpoints of each space to the left and right of the center of three of the sides. Remember to leave one side (in our case, the bottom) of the cushion open.
Pet Snuggle Bed Make a Gather
The excess fabric will need to be gathered to lay flat.
Now you need to create pleats. Remember, you will have excess fabric on top because it’s bigger than the base. Simply pinch the fabric into a fold until it lines up with the cushion cover on the bottom. Then, fold the fabric over to one side and pin down. Fold each pleat in the same direction. After you complete this for each side of the cushion, you should now have three sides pinned down. Sew the top to the cushion cover.
Create a Custom Look
Snuggle Pet Beds in Blue and Chevron
These snuggle pet beds are great for pets of all sizes.
Play around with different contrasting colors and patterns for a custom look. When it needs to be washed, simply remove the cover and pop it in the washer and dryer.
Make Your Pet Happy
Two Dogs in Pet Beds with Blanket
Dogs of all shapes and sizes love to snuggle under covers.
Pets of all shapes and sizes love to snuggle. The best part of this project is that it can be customized to fit any special furry friend. The snuggle pet bed also makes a great gift for animal lovers.
We turned an old flea-market dresser into a combination bedside table and pet bed. To make it, we cut out the bottom two drawers and relined them with beadboard, then coated the entire piece in a fun color. A fluffy cushion in the bottom makes it a welcoming retreat.
Stylish and Multifunctional
Octagon tables were all the rage 40 years ago; today you can find them secondhand for next to nothing. We updated this one by removing the door and giving the whole piece a fresh coat of paint. Then we made it pet friendly by lining the inside with fabric and adding an inviting cushion.
Modern End Table
This stylish end table with its peek-a-boo sides adds a perfect mod accent and serves a dual purpose as an end table and raised perch for lounging.
Drawer Turned Bed
This simple project requires very little power-tool skills. New furniture feet were screwed onto the base of an old dresser drawer, then the entire piece was painted. Wood letters were adhered to the front to identify the new owner.
This portable pet carrier is easy to make and doesn't cost a lot. The mesh top is removable so the basket can be used for an outing or at home as a pet bed.
To make this comfy chair, the legs were cut off an old office chair. Furniture pads were added to the bottom to restabilize it. Then the entire chair was covered in a soft blanket and felt letters.